Відео

So if you go into settings you can select the mode you want the exhaust to stay in. There is absolutely no need to pull a fuse unless you just don't know how your vehicle operates.

if you over tighten the oil filter cap you can crack the cooler housing.

Do you mind me asking what you do for your income

is it posible install at Jeep grand cherokee 3.6l 2014 ??

How can they just cancel like that without any notification? Especially if your insurance was paid in advance. You could probably sue them if that was the case.

THANK YOU!! I have the exact pistol. Cannot wait to custom it out!

I heard it’s a nightmare to put this thing together though instructional videos are horrible instructions that come with it are horrible. Some people said it took them four hours just to put it together other than that. Looks like a great idea once it’s together.

I owned a GT3rs and is not working for me.

Good job man

She needs to stay in the kitchen

Need to remove the oil filter first to allow oil to drain down into the oil pan from the oil filter housing since it’s a cartridge oil filter.

Installed these today. Key thing is the short fat socket to lock the spring in the bracket to a bent position. Skip the zip ties and leave one stud nut loosened on one end. You can get the brackets in place without removing the rubi rails. Leave the socket in place until the step is attached with pins, socket comes right out when step is depressed 👌🏼

so you can replace the batteries without screwing up the computer???

Nice vid

Man that engine noise worried me till I seen it in every cold start video on these bikes 😅

Is there no KingPins (pins) to inspect ? I also noted it has no pad-key stainless clips as the T&C have & the rear pistons does not need to be turned in with your tool, just pressed in & maybe out for easy seal-ring replacements. I was thinking about shifting my 11 ø300 to 14's ø330mm 2 pistons in the front. But now i will check if possible to get Pacifica Calipers seems better tobseevice and probably better anti-hanging

FYI there should be a bolt with a label that is specifically there for grounding (usually on driver's side)

G wagon

Nice

there is a ground post for the negative connection. use that. its on the driver side of the compartment and is labelled as a negative terminal. its on the pillar that the wiper system is attached to. also, better to use just a trickle charger to pop the bonnet using the fuse box connector, you don't need to use a jump box. this connector is not a fuse by the way, it is a positive terminal to power the hood latch. lastly, the LifePO4 battery is not likely "dead". it is just sleeping. The battery has internal circuity that protects it against excessive discharge which puts it to sleep. it just need a little kick to wake up. if your battery is truly dead, you will need to replace it. if you attempt to jump a truly dead lithium battery, you may start a fire. call for service/tow. you can use another car to jump the car as long as you use the negative terminal post and not the negative battery terminal. you can also charge it for at least 10 minutes with a lithium ion capable trickle charger.

You are misleading people. Please read the manual. Rear skid were installed wrong. In addition, you should always keep control arm same length. Because left right corner bear different weight, the hole won’t align unless you lift pinion a little bit. By adjusting the length, now you have a bad thrust angle.

You put the H7 battery in and it only takes the H6 battery. H7 is to high.

can you lift the TLP with the top on to give you more clearance for the hood?

Thanks, you do a great job, probably the best how to video I've seen.

What? Won't penetrate? Like Hell it won't !!!

thank you for a very informative video.

Had no idea that you had to go into settings to change the pads!

Is it the same process for the front? Thank you

Brilliant. You tried to stuff a H7 DieHard battery into a H6 slot. Gee, wonder why it didn't fit?!

where did u get the tow kit ?

Very nice 👍

Your in Vegas and this is what you did lollll

that looks so cool, but if I were to go up there I would be dying bc I'm so scared of hights.😂

My friend, you should start with traction off and from 3k rpm to get proper result, holding both pedals together

Thank you for the informative video! It saved me a lot of time and effort. I'm not used to working on anything newer than my '99 Cherokee, and all the extra stuff on newer cars is a little baffling at first glance 😄

What about food poisoning

No clue what an egg beer is but should for sure try it

Thanks for this video now I'm able to mount my sling and attachments

Have any videos on how you remove stock exhaust?

Give me all the G wag content 🥹

13years passed 😢

❤

What quad rail is this and where did you get it from ?

Stop your interview and just sell the car let somebody enjoy it. You don’t need it.

Nice

Looks fuckin delicious

Nice any 1/4 runs ???

Save my life in 2024

Are you under water or did your mic fall into the garbage disposal??

Awesome video bro, just what I was looking for. Thank you!